MAMUT GLUE, CRYSTAL, white, 290ml

CHARACTERISTICS
Universal one-component acid-curing silicone sealant. Adheres well to metal, glass, glazed surfaces, ceramic tiles, impregnated, varnished or painted wood, varnished surfaces and many plastics, e.g. epoxy, polyester, polyacrylate, laminate. It does not bend, it does not expand in the joint. Allows for long working hours. Cured silicone is resistant to UV radiation.

USE
It is used for sealing ceramic elements, porcelain and aluminum joints, sealing window and door frames, ventilation and drainage systems, electrical cables and wires.
The product has been tested and is classified accordingly:
Facade putty for interior use.

APPLICATION PROCEDURE
Use temperature between +5 °C and +40 °C. The application temperature of the sealant must be +20 °C - +25 °C. Application at temperatures below +5 °C can only be carried out when the connected surfaces are free of condensation, snow and ice. Do not use in contact with fiber cement and mortar and with natural stones such as marble and granite. Do not use in contact with metals such as lead, copper, brass and zinc due to corrosion. Silicone can change color when in contact with some organic elastomers, eg EPDM and neoprene. Not suitable for sealing aquariums and for use under water. Cannot be painted.

SURFACE PREPARATION
The surfaces must be cleaned of dust, loose particles and oil. Non-porous surfaces should be cleaned with solvent and a clean, lint-free cotton cloth. Solvent residues must be removed with a clean cloth before evaporation.

METHOD OF CLEANING
310 ml cartridge: Cut off the threaded end of the cartridge and screw on the application nozzle to direct the sealant.
Cut the threaded end to create a suitable opening for application.
Insert the cartridge together with the applicator into the gun and press the gun trigger repeatedly to fill the installation nozzle with sealant.

600 ml foil pack: Open the application nozzle of the gun, insert the pack into the gun and open the side of the applicator by removing the retaining clip.
Place the application nozzle on the open end and screw on the cap.
Apply the sealant to the joint by repeatedly and evenly pressing the trigger of the gun and smoothly pulling the nozzle along the joint.
After application, smooth the surface with a rubber silicone scraper and remove excess material.
Ensure adequate ventilation during application.
The maximum recommended joint size is 30x20 mm.
Can be used with reinforcing fabric.
Ensure adequate ventilation at all joints.
During curing, make sure that no dirt settles on the surface and that the joint surface is not subjected to mechanical stress.

CLEANING
Unhardened sealant, tools and hands can be cleaned with PENOSIL Premium cleaning wipes. Hardened sealant can be removed mechanically using PENOSIL Premium Silicone Remover to soften the sealant. Clean the surface with a cloth and water.

SPECIFICATIONS
Structure creation time min. 10-12
Curing time mm/24 h 2-3
Density (DIN53 479-B) g/cm3 0.96 - transparent 1.08 - colored
Joint movement, ISO 11600% ± 12.5
Microbiological growth intensity, ISO846 1 – transparent 2 – colored
Flow resistance, ISO7390 mm 0
Volume change, ISO10563%
40 ± 1 – transparent
35 ± 1 – colored
Elongation at break, ISO37%
750 ± 25 – transparent
550 ± 25 – color
Tensile strength, ISO37 N/mm2
2.2 ± 0.2 – transparent
2.2 ± 0.2 – colored
Modulus at 100% elongation, ISO 37 N/mm2
0.4 ± 0.1 – transparent
0.7 ± 0.1 – colored
Hardness (Shore A) (ISO 868) 30 ± 2 – transparent
40 ± 2 – colored
Temperature resistance °C -40 to +10

SECURITY REQUIREMENTS
Keep out of reach of children.
Avoid contact with skin and eyes.
In case of eye contact, rinse immediately with water and seek medical attention.
The hardened sealant can be handled without risk to health.
Detailed safety information is available in the safety data sheet (SDS).